Yes, in New Orleans an aluminum gate can often be repaired by welding when the break sits in solid metal and the alloy welds well. Unlike steel, the metal beside an aluminum weld is usually the weak point, according to The WELDER's 2014 Aluminum Workshop column. Coatings come off the joint, heat stays low, and any steel hardware touching the frame is checked for corrosion.
Last Updated: November 16, 2026
Table of Contents
- Can You Weld an Aluminum Gate in New Orleans, LA?
- What Usually Breaks on an Aluminum Gate in New Orleans?
- Why Does Aluminum Gate Repair Differ From Steel in New Orleans?
- Which Aluminum Gate Problems Can Be Fixed on Site in New Orleans?
- Getting a Cracked Aluminum Gate Swinging Again
- Frequently Asked Questions
An aluminum gate with a split corner, a loose hinge tab or a snapped latch often still has plenty of sound metal in it. The real question is whether the break sits somewhere a weld can reach and hold.
At Big Easy Mobile Welders, we weld broken aluminum gates as well as steel and wrought iron ones. That work falls under our mobile welding services for New Orleans homes and businesses, so the welder brings the rig to the gate.
This page covers what tends to break on aluminum gates and why the repair differs from steel. It also sorts the problems a welder can usually fix on site from the ones that need a new part.
Can You Weld an Aluminum Gate in New Orleans, LA?
Yes, an aluminum gate in New Orleans can usually be welded when the crack runs through sound metal and the alloy welds well. TWI's aluminum alloy guide, first published in 1996, lists the 6xxx series among wrought grades that can be fusion welded. Our page on aluminum welding repairs covers other aluminum parts.
Hydro, a maker of aluminum extrusions, describes 6063 as an architectural alloy that can handle moderate loads. Gate frames are often extruded, so a 6xxx grade is a reasonable first guess until the maker's details confirm it. If you are weighing a new gate instead, our aluminum and steel comparison covers that choice.
Our gate welding service handles frames, hinges and latches on gates made of steel, stainless, aluminum or wrought iron. With aluminum, the prep, heat and checks change, as the sections below explain.
What Usually Breaks on an Aluminum Gate in New Orleans?
On an aluminum gate in New Orleans, damage usually shows up in four places, and each has its own cause. The four are the frame corners, the hinge and latch mounts, any spot where steel touches aluminum, and the metal right beside an older weld.
Split Welds at the Frame Corners

Every swing and every slam pushes on the corners where the rails meet the upright stiles. In time a corner weld can split, letting the frame rack out of square.
A split corner is often a clean repair, because the break sits in a joint that was already welded once. The old crack is ground out and the joint is welded back to full depth.
A frame that has racked for a while may strain the opposite corner too, so both get checked.
Broken Hinge and Latch Mounts
Hinge tabs and latch brackets carry the leaf's weight along with every hard close. On an aluminum gate, those small welded parts are a frequent point of failure.
A broken tab can often be welded back in place, or a new aluminum tab can be fitted where the old one was. The replacement part has to match the gate's metal so the joint welds cleanly.
Because each metal takes its own settings and filler, we confirm what the gate is made of ahead of the visit.
Corrosion Where Steel Meets Aluminum
Aluminum gates often hang from steel posts or carry steel hinges, bolts and latches. TWI's guidance on galvanic corrosion uses aluminum connected to carbon steel in seawater as its example.
In that pairing, the aluminum corrodes faster while the steel is protected. Salt air and rain make those contact points worth checking during any repair.
TWI lists insulating the two metals, coating both of them, and fitting a spacer between them as ways to prevent it. Our article on keeping welded metal free of rust covers coatings after a repair. Galvanized posts raise their own issues, explained in our guide to welding galvanized steel.
Cracks Next to an Earlier Weld
Sometimes the crack runs through the metal right beside the weld. TWI's 1996 guide explains that liquation cracking forms in the heat-affected zone, the band of metal just outside a weld.
The same guide notes that heat-treatable alloys, especially the 6xxx and 7xxx series, are more prone to it.
A crack in that zone needs more than a fresh bead laid over the top. It has to be removed fully, and the welder then judges whether enough sound metal remains around it.
Why Does Aluminum Gate Repair Differ From Steel in New Orleans?
Aluminum gate repair in New Orleans differs from steel in three ways that shape the whole job. The metal beside the weld loses strength, heat has to stay controlled, and any paint or powder coat must come off the joint first.
The Weak Point Moves Beside the Weld

With steel, the weld itself is often treated as the weak spot in a joint. In a 2014 Aluminum Workshop column for The WELDER, Frank Armao writes that with aluminum, the heat-affected zone usually is.
The same column notes that on 6061 and other 6xxx alloys, the weld metal is almost always stronger than that zone. For a gate, that means a repaired joint is judged by the metal around it, not only by how the bead looks.
That is why the welder checks how much solid aluminum surrounds a break before deciding to weld it.
Keeping Heat Under Control
Steel welders sometimes preheat thick parts, but aluminum gate work follows different rules. In a second 2014 Aluminum Workshop column, Armao writes that aluminum alloys generally do not need preheat to be welded.
If preheat is used, the column limits it to 200 degrees F. It warns that heating 6061-T6 to between 300 and 600 degrees F destroys its T6 properties before an arc is struck.
So on a heat-treated gate frame, the welder keeps added heat to a minimum. The column adds that a mild preheat often helps drive off condensation, useful on a humid New Orleans morning.
Stripping Coatings and Oxide
Aluminum gates usually come painted or powder coated, and that finish cannot stay on the joint. TWI's porosity guide, first published in 1999, says to remove surface coatings from the joint area down to bright metal.
The same guide also warns that very thick paint or primer can release enough gas to leave cavities known as wormholes in the weld.
TWI's separate guide on avoiding porosity in aluminum adds that its oxide film takes up moisture from the surrounding air. Once the weld is done, the bare area needs a protective finish again.
Which Aluminum Gate Problems Can Be Fixed on Site in New Orleans?
Many aluminum gate problems in New Orleans, Metairie, Kenner and Mandeville can be welded right where the gate hangs, with no trip to a shop. The table below shows how common symptoms usually sort out once a welder has seen the gate in person.
| Symptom | What It Often Points To | Usual Outlook |
|---|---|---|
| Split weld at a frame corner | Strain from daily swinging and slamming | Usually rewelded on site |
| Hinge tab or latch bracket broken off | Load and impact on a small welded part | Rewelded, or a new aluminum tab fitted |
| Pitting where steel hardware touches the frame | Galvanic corrosion between the two metals | Sound metal repaired, then the metals separated |
| Crack just beside an older weld | Cracking in the heat-affected zone | Depends on how much solid metal remains |
| Long stretches thinned by corrosion | Years of exposure to salt and moisture | Often better replaced with a new section |
Our article on welding fixes after storm damage covers gates bent by wind or debris. The fence beside a gate takes the same weather, so fence welding can be added to the visit.
Our overview of common welding techniques for gates and fencing explains the methods behind this work. To plan the repair, send pictures showing the crack and the full gate through our online estimate request form.
Getting a Cracked Aluminum Gate Swinging Again
A cracked or broken aluminum gate is often worth welding when the damaged area still has plenty of solid metal around it. Strength beside the weld, careful heat control and a clean, coating-free joint decide whether the repair holds up over time.
At Big Easy Mobile Welders, we check the gate's metal before the visit and quote the repair at no charge. Call (504) 370-2757 to book a free gate estimate and find out whether your aluminum frame can be welded.
Frequently Asked Questions
Does welding weaken aluminum?
Yes, welding can lower the strength of aluminum in the band of metal right next to the weld. Frank Armao's 2014 column in The WELDER says the heat-affected zone on 6061 and similar alloys is almost always weaker than the weld metal.
Can aluminum gates rust?
No, aluminum gates do not rust the way steel gates do, since rust is an iron oxide. TWI notes that aluminum forms a thin, tenacious oxide film as soon as it meets air, which gives it good corrosion resistance. The steel posts, bolts and hinges on an aluminum gate can still rust.
Can aluminum and steel touch?
Aluminum and steel can touch, but the contact point can corrode the aluminum when moisture or salt water connects the two metals. TWI's galvanic corrosion guidance lists insulating the metals from each other, coating both, or adding a spacer as ways to prevent it. Hinges and posts are the usual contact points on a gate.
Can you weld powder coated aluminum?
Powder coated aluminum can be welded once the coating is removed, since TWI's 1999 porosity guide calls for bare, bright metal at the joint. A thick coating left on the joint can put gas into the weld. The finish is cleared around the break first and replaced after the repair.
Why do aluminum welds crack?
Aluminum welds can crack because the metal expands and shrinks sharply with heating and cooling. TWI's 1996 guide puts aluminum's thermal expansion at twice that of steel. It also names 6xxx and 7xxx alloys as more prone to cracking beside the weld.
How much does it cost to repair a metal gate?
The cost to repair a metal gate depends on the metal, the gate's type and size, its design and the parts it needs. Aluminum can call for more filler and time than a light steel repair. A free estimate gives you a firm figure before the work is booked.
How long do aluminum gates last?
There is no fixed lifespan for an aluminum gate. It depends on the alloy, the finish, the hardware and how much salt and moisture the gate sees. Aluminum resists rust well, so the hinges, fasteners and welds are the parts to watch.
