Welded wire fencing is a type of fencing that is made of welded wire mesh. The mesh is made of low-carbon steel wire that is welded at each intersection. Welded wire fencing is also called weldmesh, WWM, or weldmesh fencing. It is used in a variety of applications, including agricultural, commercial, industrial, and residential.
Installing welded wire fencing is not as difficult as you might think. In fact, it’s a fairly straightforward process that can be completed in a few hours with the help of a friend or two. However, before you begin, there are a few things you’ll need to do in order to ensure that the job is done right. Here are the basic steps on how to install welded wire fencing.
When it comes to installing a welded wire fence, there are a few key materials you will need in order to get the job done. These materials include:
One of the most important steps in the installation process is gathering all of the necessary materials before you get started.
This will ensure that you have everything you need on hand and that you are not running back and forth to the hardware store in the middle of the project.
When it comes to installing a welded wire fence, one of the most important steps is getting the measurements right. This can seem daunting, but it’s actually quite simple if you follow a few basic steps.
It’s important to have the proper measurements before installing a fence post. You should add two feet to the appropriate height of the fence post since a fence post is dug two feet beneath the surface of the ground.
Depending on how high you want the fence to be, you can dig deeper if you’d like, but the fence post will need to be longer to make up the difference.
You can use a shovel or a post-hole digger to dig the hole for the fence post. To ensure that your fence is the height you desire, stick to the measurements you were given.
Once you’ve dug the hole for the fence post, you should fill it with gravel. It should be about six inches. The fence post is protected from moisture by a layer of gravel. The hole should be about one-third of the height of the post, and wider at the top than at the bottom. This will help ensure that your post is stable. 
Next, you’ll need to mix some concrete. Mix the concrete according to the package directions, and then add it to the bottom of the hole. Once the concrete is in place, insert the post into the hole. Make sure the post is level and angled downward at 90 degrees. Here, having assistance is essential because even a small error could lead your fence to become uneven.
Now it’s time to level the post. This is important, as a slanted post will make it difficult to attach the fence. Use a level to make sure that the post is straight, and then add more wet concrete around it until the hole is filled.
You should wait a few days after installing the fence posts to ensure that they are fully set. For the first 24 hours, check periodically to make sure the post has not moved.
You are ready to attach the welded wire to form your fence once all of your fence posts are in place. When you have all of your materials, start by rolling out the welded wire at a corner post. Another person can assist you in holding the fencing while you or they attach the welded wire to the fence post.
To make sure the fence is taut and secure, stretch the fencing as far as you can. Stretch the wire around a corner when you get there, then carry on with the process.
In the event that you run out of material, fasten the initial roll’s end to the last post it encounters and begin a new roll on that same post. You can go back and trim the extra wire with wire clippers.
As you weld the wire to the fence posts, it’s crucial to make sure the fencing stays level. To ensure that the fencing is level, it is useful to halt every other fence post.
Although not all fences have gates, if you do, I advise installing them last. The posts that support the gate should already be in place. Typically, it is situated between two fence posts, a fence post, and a house or other substantial building.
Measure the distance between the support posts to get the gate’s width, then subtract around 2 inches. The hinges and latch have enough room as a result. There won’t be enough room for the gate to swing if the gate is made to fit exactly between two posts.
To ensure that the gate will swing, dry fit it in the opening. Prior to attaching the hinges to the post, attach them to the gate. It resembles hanging a door in a frame exactly. Ensure that the hinges are set up squarely and levelly. When you open and close the gate, the hinges will twist if they are even slightly out of alignment.
Install the handle or latch after the gate has been hung. To fasten the hinges to the post, use screws. The weight of the gate could pull the screws out if they are too short.
Planning is the key to any successful home improvement project, and that includes installing a welded wire fence. Carefully consider your needs and wants for the fence, such as height, material, and placement.
Once you have a good idea of what you need, research the different types of welded wire fences and find the one that best suits your needs. When you’re ready to purchase the materials for your fence, be sure to get everything you need in one trip to the store.
This will save you time and money in the long run.
Looking for a company that offers mobile welding services in New Orleans? Look no further than Big Easy Mobile Welders. We offer a variety of welding services to meet your needs, and our team is always available to answer any questions you may have. Contact us today to get started on your next project!
By Admin 
0 Comment 
Nov 15, 2022